Get 100% Real 300-410 Exam Questions, Accurate & Verified Answers As Seen in the Real Exam!
300-410 Premium Files Updated Jul-2023 Practice Valid Exam Dumps Question
The Cisco 300-410 exam is a challenging test that requires thorough preparation and understanding of the concepts. Cisco offers a range of resources to help candidates prepare, including online courses, study materials, and practice exams. Candidates can also participate in the Cisco Learning Network community to connect with other professionals and gain insights from experts.
The Cisco 300-410 exam is all about the implementation of Cisco enterprise advanced routing and services. It also evaluates one’s knowledge and skills in troubleshooting routing services and technologies, infrastructure security, infrastructure automation, infrastructure services, VPN services, and Layer 3.
NEW QUESTION # 248
Refer to the exhibit.
An engineer configures DMVPN and receives the hub location prefix of 10.1.1.0724 on R2 and R3 The R3 prefix of 10 1.3.0/24 is not received on R2. and the R2 prefix 10.1,2.0/24 is not received on R3. Which action reserves the issue?
- A. Split horizon prevents the routes from being advertised between spoke routers it should be disabled with the command no ip split-horizon eigrp 10 on the tunnel interface of R1
- B. There is no spoke-to-spoke connection DMVPN configuration should be modified to enable a tunnel connection between R2 and R3 and neighbor relationship confirmed by use of the show ip eigrp neighbor command
- C. There is no spoke-to-spoke connection DMVPN configuration should be modified with a manual neighbor relationship configured between R2 and R3 and confirmed bb use of the show ip eigrp neighbor command.
- D. Split horizon prevents the routes from being advertised between spoke routers it should be disabled with the no ip split-horizon eigrp 10 command on the Gi0/0 interface of R1.
Answer: A
Explanation:
Explanation
In this topology, the Hub router will receive advertisements from R2 Spoke router on its tunnel interface. The problem here is that it also has a connection with R3 Spoke on that same tunnel interface. If we don't disable split-horizon, then the Hub will not relay routes from R2 to R3 and the other way around. That is because it received those routes on the same interface tunnel and therefore it cannot advertise back out that same interface (split-horizon rule). Therefore we must disable splithorizon on the Hub router to make sure the Spokes know about each other.
NEW QUESTION # 249
Refer to the exhibit.
Which control plane policy limits BGP traffic that is destined to the CPU to 1 Mbps and ignores BGP traffic that is sent at higher rate?
- A. policy-map LIMIT_BGP
- B. policy-map POLICE_BGP
- C. policy-map COPP
- D. policy-map SHAPE_BGP
Answer: C
NEW QUESTION # 250
Refer to the exhibit.
ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console. Which command is missing from the IP SLA configuration?
- A. Start-time 00:00
- B. Start-time immediately
- C. Start-time 0
- D. Start-time now
Answer: D
NEW QUESTION # 251
Which protocol does VRF-Lite support?
- A. IGRP
- B. IS-IS
- C. ODR
- D. EIGRP
Answer: D
NEW QUESTION # 252
Refer to the exhibit.
A user has set up an IP SLA probe to test if a non-SLA host web server on IP address 10.1.1.1 accepts HTTP sessions prior to deployment. The probe is failing. Which action should the network administrator recommend for the probe to succeed?
- A. Add icmp-echo command for the host.
- B. Re-issue the ip sla schedule command.
- C. Modify the ip sla schedule frequency to forever.
- D. Add the control disable option to the tcp connect.
Answer: D
NEW QUESTION # 253
Refer to the exhibit.
An administrator that is connected to the console does not see debug messages when remote users log in. Which action ensures that debug messages are displayed for remote logins?
- A. Enter the terminal monitor exec command.
- B. Enter the aaa new-model configuration command.
- C. Enter the logging console debugging configuration command.
- D. Enter the transport input ssh configuration command.
Answer: A
NEW QUESTION # 254
Refer to the exhibit.
After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both spoke-to-spoke and hub were not establishing.
Which two actions resolved the issue? (Choose two.)
- A. Configure the crypto isakmp key cisco address 0.0.0.0 on R2 and R3.
- B. Remove the crypto isakmp key cisco address 10.1.1.1. on R2 and R3.
- C. Configure the crypto isakmp key cisco address 192.1.1.1 on R2 and R3.
- D. Configure the mode from mode tunnel to mode transport on R3.
- E. Change the mode from mode transport to mode tunnel on R2.
Answer: A,D
NEW QUESTION # 255
Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.
Answer:
Explanation:
NEW QUESTION # 256
Which two protocols can cause TCP starvation? (Choose two)
- A. SNMP
- B. SMTP
- C. FTP
- D. HTTPS
- E. TFTP
Answer: A,E
NEW QUESTION # 257
Refer to the exhibit.
An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through router R2. Which debug command is used to troubleshoot this issue?
- A. debug ip routing
- B. debug ip packet
- C. debug ip flow
- D. debug ip sla error
Answer: A
Explanation:
Explanation
debug ip routing This command enables debugging messages related to the routing table.
NEW QUESTION # 258
Refer to the exhibit.
R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?
- A. Route reflector setup requires full IBGP mesh between the routers.
- B. In route reflector setups, prefixes are not advertised from one client to another.
- C. R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.
- D. In route reflector setup, only classful prefixes are advertised to other clients.
Answer: C
NEW QUESTION # 259
Refer to the exhibit.
An administrator must configure the router with OSPF for IPv4 and IPv6 networks under a single process. The OSPF adjacencies are not established and did not meet the requirement. Which action resolves the issue?
- A. Replace OSPF process 10 on the interface with OSPF process 1 for the IPv4 address, and remove process 10 from the global configuration.
- B. Replace OSPF process 10 on the interface with OSPF process 1, for the VPv6 addressma nd remove process route ID with IPv6 address.
- C. Replace OSPF process 10 on the interface with OSPF process 1, and remove process 10 from the global configuration.
- D. Replace OSPF process 10 on the interface with OSPF process 1, and configure an additional router ID with IPv6 address.
Answer: C
NEW QUESTION # 260
Refer to the exhibit.
Refer to the exhibit. After reloading the router an administrator discovered that the interface utilization graphs displayed inconsistencies with their previous history in the NMS. Which action prevents this issue from occurring after another router reload in the future?
- A. Save the router configuration to startup-config before reloading the router
- B. Configure SNMP interface index persistence on the router
- C. Configure SNMP to use static OlDs referring to individual router interfaces
- D. Rediscover all the router interfaces through SNMP after the router is reloaded
Answer: B
NEW QUESTION # 261
Refer to the exhibit.
The administrator noticed that the connection was flapping between the two ISPs instead of switching to ISP2 when the ISP1 failed. Which action resolves the issue?
- A. Include a valid source-interface keyword in the icmp-echo statement.
- B. Modify the static routes to refer both to the next hop and the outgoing intertace.
- C. Modify the threshold to match the administrative distance of the ISP2 route.
- D. Reference the track object 1 on the default route through ISP2 instead of ISP1.
Answer: A
Explanation:
Explanation
https://www.cisco.com/c/en/us/support/docs/ip/ip-routing/200785-ISP-Failover-withdefault- routes-using-I.html
NEW QUESTION # 262
Refer to the exhibit.
After redistribution is enabled between the routing protocols; PC2, PC3, and PC4 cannot reach PC1. Which action can the engineer take to solve the issue so that all the PCs are reachable?
- A. Filter the prefix 10.1.1.0/24 when redistributed from OSPF to EIGRP.
- B. Redistribute the directly connected interfaces on R2.
- C. Set the administrative distance 100 under the RIP process on R2.
- D. Filter the prefix 10.1.1.0/24 when redistributed from RIP to EIGRP.
Answer: A
NEW QUESTION # 263
Refer to the exhibit.
Refer to the exhibit. Site1 must perform unequal cost load balancing toward the segments behind Site2 and Site3. Some of the routes are getting load balanced but others are not. Which configuration allows Site1 to load balance toward all the LAN segments of the remote routers?
- A. Option D
- B. Option A
- C. Option C
- D. Option B
Answer: A
NEW QUESTION # 264
Refer to Exhibit.
Traffic from the branch network should route through HQ R1 unless the path is unavailable. An engineer tests this functionality by shutting down interface on the BRANCH router toward HQ_R1 router but 192.168.20.0/24 is no longer reachable from the branch router. Which set of configurations resolves the issue?
- A. BRANCH(config)# ip sla 1
BRANCH(config-ip-sla)# icmp-echo 172.16.35.2 - B. BRANCH(config)# ip sla 1
BRANCH(config-ip-sla)# icmp-echo 172.16.35.1 - C. HQ_R2(config)# ip sla responder
HQ_R2(config)# ip sla responder icmp-echo 172.16.35.5 - D. HQ_R1(config)# ip sla responder
HQ_R1(config)# ip sla responder icmp-echo 172.16.35.2
Answer: A
Explanation:
In the configuration above, the engineer has made a mistake as he was tracking 172.16.35.6 (the backup path) instead of tracking the main path (172.16.35.2). Therefore,when he shut down the main path, the track 1 was still up so traffic still went through the main path -> it failed.
To fix this issue, we just need to correct the tracking interface of the main path.
NEW QUESTION # 265
......
REAL 300-410 Exam Questions With 100% Refund Guarantee : https://exampdf.dumpsactual.com/300-410-actualtests-dumps.html
